Heating guide

Should you replace your furnace and air conditioner together?

The furnace and the central AC share more hardware than most people expect, which is why replacing one sometimes means looking hard at the other too.

Toronto Mechanical Services · Updated September 2026

Furnace not heating or something else wrong? Call and tell us what it is doing.

Call (647) 674-2387

Why furnace and AC often get replaced together

The furnace and the central AC share more hardware than people expect. The AC's indoor coil usually sits directly on top of the furnace, the furnace's blower pushes air across that coil, and refrigerant lines connect the coil to the outdoor condenser. Replace one half of that pairing without looking at the other, and there's a real chance the new part and the old one don't work well together.

The indoor coil sits on the furnace

When a furnace is replaced, the plenum and duct connections at the top of it change shape, and the existing AC coil has to be refitted to the new furnace, or in some cases doesn't fit cleanly at all. New furnaces are rarely the exact same dimensions as the old one. If the coil is old, refitting an aging coil to a brand-new furnace can mean paying labour twice: once now, and again in a few years when the coil finally needs replacing anyway.

Blower matched to AC capacity, and the ductwork between them

The furnace's blower has to move enough air across the AC's coil for the system to cool properly and pull humidity out of the air, which matters on a humid Toronto afternoon. A blower sized for the old AC doesn't automatically suit a different capacity or a different type of coil. When we replace a furnace, we check that its blower still matches the AC it's paired with, and vice versa when we replace the AC.

Whether the furnace and AC are replaced together or separately, the same ductwork carries the air for both, and a duct system that was already tight or leaky doesn't get better on its own just because new equipment is going in. When we're pricing a combined replacement, we look at the ducts once for both systems instead of twice, which is one of the places a joint visit saves real steps compared with two separate ones.

Refrigerant changes

Air conditioners from before about 2010 often run on R-22, which is no longer made or imported in Canada. An old R-22 outdoor unit paired with a coil never designed for a newer refrigerant isn't something to mix and match; replacing one side of an R-22 system usually means replacing the refrigerant circuit as a whole. If your AC is on R-22 and the furnace is also due, that's one more reason to look at both at once rather than patching the AC side later.

One install date instead of two

Doing both at the same visit means the furnace, the coil, and the outdoor unit all go in matched, tested, and started up together, rather than an old coil bridging two different furnace generations. It's also one visit and one disruption to the house, instead of two separate jobs months or years apart, each with its own setup and cleanup.

It also means the coil and the outdoor unit are commissioned against a furnace that's actually staying in place long-term, rather than against a furnace that itself gets swapped out a season or two later.

When it does not make sense

None of this means both should always go at once. If your AC is only a few years old, cooling properly, and not on R-22, there's usually no reason to replace it just because the furnace is due. We check the coil and confirm it will work with the new furnace's blower, and if it will, it stays. Replacing working equipment early doesn't make sense just because the timing looks convenient.

The same logic runs the other way for the furnace. A furnace that's only a few years old and running properly doesn't need replacing just because the AC has failed and needs a new coil. We check whether the existing furnace's blower can serve a new AC's coil properly before recommending anything beyond the AC itself.

A failed AC compressor or a cracked furnace heat exchanger doesn't wait for the other system's schedule, and a straight repair-or-replace decision on the failed system comes first regardless of what the other one is doing. The question of replacing both together only applies once one of them genuinely needs replacing; it isn't a reason to replace a working system early.

Timing it around Toronto's seasons

Furnace failures tend to happen in the depths of winter, and AC failures on the hottest days of summer, exactly when neither system likes being scheduled around. If you know a furnace or AC is getting old, spring and fall are the easier windows to plan a replacement, ahead of the season that would otherwise force the decision. Planning ahead also gives more room to size and quote the pair properly rather than reacting to a breakdown.

A furnace or AC showing early warning signs, rather than one that's already failed, gives the most room to plan around this timing rather than reacting to whichever one goes first.

Getting a quote

Tell us the age of both the furnace and the AC, and whether you know the AC's refrigerant type. We look at the coil, the blower, and the ductwork on a visit, and quote the furnace and AC together or separately depending on what the house actually needs. Our guide on furnace replacement cost in Toronto breaks down what goes into that side of the price, and central air conditioning covers the cooling side. If a heat pump could do both jobs from one outdoor unit, see heat pump installation. Request a visit and we'll tell you which way your house should go.

Questions

If I replace just the furnace, do I have to replace the AC coil too?

Not always, but it has to be checked. The existing coil sometimes refits to the new furnace, and sometimes it doesn't fit cleanly since new furnaces aren't always the same dimensions as the old one. We check the fit before quoting either way.

My AC is only a few years old. Does it need to be replaced with the furnace?

No, not on age alone. If it's cooling properly and isn't on R-22, we check that the coil suits the new furnace's blower and leave the AC in place if it does.

Can an old R-22 air conditioner be paired with a new furnace's coil?

Generally not directly. R-22 is no longer made or imported in Canada, and an old R-22 system's refrigerant circuit doesn't mix with equipment built for newer refrigerant. If the AC is on R-22, that circuit usually needs replacing as a whole.

Does replacing the furnace and AC together save money over doing them separately?

We can't promise a number without pricing your house, but doing both in one visit avoids paying installation labour twice on the coil and avoids a second full setup and start-up. Ask for a combined quote to compare against doing them apart.

What time of year is best to replace a furnace and AC together?

Spring and fall, ahead of the season that would otherwise force the decision. Planning the replacement before a breakdown gives more room to size and quote the pair properly.

The services

More guides

Get a written quote for furnaces

Name and phone are required.

Your service request

We’ll use your details to respond to your request. Privacy policy

  1. We call you back

    At the number you gave us, to ask what the equipment is doing.

  2. We book a window

    A day and time that works. Scheduled visits outside the regular route.

  3. Written quote before work

    You see the number before anything is replaced. Nothing starts until you say so.

CallRequest service