
Heating + cooling
Heat Pump Installationin Toronto and the GTA
Cold-climate heat pump installation and service across Toronto and the GTA. One system that heats in winter and cools in summer, sized for Toronto's coldest nights, with or without your gas furnace as backup.
- Written quote before work
- Residential + commercial
- Toronto and the GTA
Open 24 hours, 7 days a week. Call anytime.
Signs
Signs You Need Heat Pump Service in Toronto
If two or more of these sound familiar, call before it becomes a no-heat or no-cooling night.
- Not keeping up below minus 10
- Runs constantly and the electricity bill jumped
- Heavy ice on the outdoor unit that never clears
- Error code on the thermostat or head unit
- Backup heat runs more than it should
- Rooms far from the air handler stay cold
Timing: Spring and fall are the easiest times to switch to a heat pump, before the equipment you are replacing is carrying a Toronto winter or summer.
Toronto and the GTA
Heat pumps in Toronto homes
A heat pump in Toronto has to do two jobs: cool through humid summers and heat through winter nights well below minus 15 °C. How well it does the second job depends on the model, the sizing, and the house. Here is what we check before recommending one.
- 01
Cold-climate models for Toronto winters
Cold-climate heat pumps are built to keep producing heat well below freezing, where standard models fall off faster. We look at the manufacturer's rated output at low temperatures, since that number decides how much of January the heat pump can carry.
- 02
Dual-fuel with your existing gas furnace
Many Toronto houses already have a working gas furnace. A dual-fuel setup adds a heat pump that handles most of the season, and the furnace takes over in the coldest stretches. We check that the furnace, coil, and controls can work together before quoting.
- 03
Ductless heat pumps for radiator houses
Pre-war houses in the Annex, Riverdale, the Beaches, and High Park often heat with a boiler and radiators and have no ducts. Ductless heat pumps add cooling and extra heat through wall or ceiling heads, and the boiler can stay. We plan head placement room by room.
- 04
Electrical panel capacity
A heat pump needs its own circuit, and older Toronto houses sometimes have small or full panels. We look at the panel before quoting and tell you if it needs an electrician's attention first.
- 05
Sized for heating as well as cooling
An old central AC was sized to cool the house, and that size is often too small to heat it in January. We size a heat pump from the house's heat loss, then check that it still cools and dehumidifies well in summer.
- 06
Rebates
Ontario's Home Renovation Savings program currently covers qualifying heat pumps. Amounts change, and the homeowner claims it through a contractor registered with the program. Ask and we will tell you what applies to your house.
Common Heat Pump Problems We Fix in Toronto
The calls that come in most, and what is usually behind them.
Not keeping up in cold weather
Likely causes are an undersized or standard model, a low refrigerant charge, or backup heat that is not coming on. We check the charge, the backup heat controls, and the unit's rated output at that temperature.
Running constantly without shutting off
Can mean the unit is undersized for the house, or there is a refrigerant or airflow problem. We check the filter, coil, and charge before looking at size.
Ice building up on the outdoor unit
Some frost is normal and clears with a defrost cycle, while heavy ice that stays points to a defrost control, sensor, or drainage problem. We test the defrost cycle and check that meltwater can drain away.
Not cooling in summer
The causes are the same as a central AC: low refrigerant, a dirty coil, or blocked airflow. On a heat pump we also check the reversing valve.
Error codes or the unit shutting itself off
Modern heat pumps shut down rather than run damaged, and the code points to the reason. We read the code and trace the cause, whether it is a sensor, a board, or a pressure fault.
Higher electricity bills than expected
Can point to a unit running less efficiently than it should, backup electric heat running too often, or a house that needs a larger or cold-climate unit. We check the controls and backup heat settings first.
Repairs, maintenance, and replacement for heat pumps
Repairs
No heat, no cooling, error codes, or a unit that runs constantly. We diagnose ducted and ductless systems and read the fault codes before replacing parts.
Maintenance
Heat pumps run all year, so maintenance covers the heating and cooling sides, the defrost controls, and the outdoor unit. We also check that the outdoor unit sits high enough to stay clear of snow.
Installation and replacement
We size a new heat pump for your house's heat loss and heat gain, whatever the old system was. That includes the backup heat plan, whether a gas furnace or electric heat.
Cold-climate performance
Cold-climate heat pumps are built to keep producing heat well below freezing. We check how your unit actually performs in January against its rating.
Heat pumps we install
Cold-climate and standard models. Specs are the manufacturer's, not ours.
29.9 SEER2
Mitsubishi FX (Hyper-Heat)
M-Series FX · Ductless · Hyper-Heat · ENERGY STAR®
Cold-climate ductless heat pump that holds full heat to -23°C and runs to -30°C, heating and cooling for homes without ducts or for hard-to-heat rooms.
- Cooling
- 29.9 SEER2
- Heating
- 12.4 HSPF2
- Cold-climate
- Heats to -30°C
- Type
- Ductless inverter
Full specs (manufacturer)
- Model
- MUZ-FX12NLHZ + MSZ-FX12NL
- Series
- M-Series FX (Hyper-Heating H2i)
- Cooling efficiency
- 29.9 SEER2 (9k model: 33.1)
- Heating efficiency
- 12.4 HSPF2
- Cold-climate
- 100% heat at -23°C · operates to -30°C
- Type
- Variable-speed inverter (ductless)
- Indoor sound
- 21 – 42 dB(A)
- Refrigerant
- R-454B (low-GWP)
- Capacity
- 12,000 BTU/h · single-zone (multi-zone available)
- Warranty
- 10-year compressor & parts (with registration)
- Certifications
- ENERGY STAR® Certified
ENERGY STAR certified as published by the manufacturer for this model.
up to 23 SEER2KeepRiteKeepRite Ion 23
Ion™ 23 · Variable-speed · ENERGY STAR®
Canadian-built variable-speed cold-climate heat pump that heats down to -13°F (-25°C) with top-tier efficiency on the new R-454B refrigerant.
- Cooling
- Up to 23 SEER2
- Heating
- Up to 12 HSPF2
- Cold-climate
- Heats to -13°F
- Compressor
- Variable-speed
Full specs (manufacturer)
- Model
- C5H3V (Ion™ 23)
- Cooling efficiency
- Up to 23 SEER2
- Heating efficiency
- Up to 12 HSPF2
- Compressor
- Fully variable-speed (20–100%)
- Cold-climate
- Heating operation down to -13°F (-25°C)
- Sound level
- As low as 55 dB
- Refrigerant
- R-454B (low-GWP)
- Sizes
- 2 – 5 tons
- Compressor warranty
- 10-year limited
- Parts warranty
- 10-year (with registration)
- Certifications
- ENERGY STAR® Qualified
ENERGY STAR certified as published by the manufacturer for this model.
19+ SEER2
York YZV (Affinity)
Affinity™ · Variable-capacity · ENERGY STAR® Most Efficient
York's premium inverter heat pump, with variable capacity for quiet, precise year-round comfort and a lifetime compressor warranty.
- Cooling
- 19+ SEER2
- Heating
- 9.0 HSPF2
- Compressor
- Variable-capacity
- Warranty
- Lifetime compressor
Full specs (manufacturer)
- Model
- YZV (Affinity)
- Cooling efficiency
- 19+ SEER2 (up to 21 SEER)
- Heating efficiency
- 9.0 HSPF2
- Compressor
- Variable-capacity (variable-speed scroll)
- Sound level
- As low as 54 dBA
- Refrigerant
- R-410A
- Sizes
- 2 – 5 tons
- Compressor warranty
- Lifetime limited
- Parts warranty
- 10-year limited (with registration)
- Certifications
- ENERGY STAR® Most Efficient
ENERGY STAR certified as published by the manufacturer for this model.
up to 17 SEER2
Lennox EL16KP1
Elite® Series · Single-stage · ENERGY STAR®
An efficient single-stage heat pump on the new R-454B refrigerant: a strong-value year-round heating-and-cooling upgrade.
- Cooling
- Up to 17 SEER2
- Heating
- 8.5 HSPF2
- Cooling stage
- Single-stage
- Refrigerant
- R-454B
Full specs (manufacturer)
- Model
- EL16KP1
- Series
- Elite® Series
- Cooling efficiency
- 16.8 – 17 SEER2
- Heating efficiency
- 8.5 HSPF2
- Cooling stage
- Single-stage
- Sound level
- As low as 71 dB
- Refrigerant
- R-454B (low-GWP)
- Sizes
- 1.5 – 5 tons
- Compressor warranty
- 10-year limited
- Parts warranty
- 5-year (10-year with registration)
- Certifications
- ENERGY STAR® qualified
ENERGY STAR certified as published by the manufacturer for this model.
up to 18 SEER2KeplerKepler LUXE (Ultra Heat)
LUXE · Inverter · Cold-climate
Kepler's premium inverter cold-climate heat pump, rated to keep heating down to -30°C. A value-priced Canadian option.
- Cooling
- Up to 18 SEER2
- Heating
- 9.5 HSPF2
- Cold-climate
- Rated to -30°C
- Compressor
- Inverter
Full specs (manufacturer)
- Series
- LUXE (Ultra Heat)
- Cooling efficiency
- Up to 18 SEER2 (16.3 @ 3-ton)
- Heating efficiency
- 9.5 HSPF2 (3-ton, Region IV)
- Compressor
- Inverter-driven (1% increments)
- Cold-climate
- Ultra Heat: rated to -30°C
- Sound level
- 62 – 65 dB(A)
- Refrigerant
- R-410A
- Sizes
- 1.5 – 5 tons (18k – 60k BTU)
- Warranty
- 10-year compressor & parts (12-year via authorized dealer)
up to 16.2 SEER2
Trane XR16 Heat Pump
XR Series · Two-stage
Trane's reliable two-stage heat pump with a Climatuff® compressor for steady year-round comfort, often paired with a furnace for cold snaps.
- Cooling
- Up to 16.2 SEER2
- Heating
- Up to 8.1 HSPF2
- Compressor
- Two-stage Climatuff®
- Refrigerant
- R-410A
Full specs (manufacturer)
- Model
- 4TWR6 (XR16 Heat Pump)
- Cooling efficiency
- Up to 16.2 SEER2
- Heating efficiency
- Up to 8.1 HSPF2
- Compressor
- Two-stage Climatuff®
- Sound level
- 72 dB(A) (74 on 5-ton)
- Refrigerant
- R-410A
- Sizes
- 2 – 5 tons
- Compressor warranty
- 10-year (registered)
- Parts warranty
- 10-year (registered)
Specs as published by each manufacturer. Models shown are examples; the unit we quote depends on the house.
Your options: types, not brands. We match the type to the house, then pick the unit.
Ducted air-source
Connects to existing ductwork and replaces or works alongside a furnace and central AC.
Best for: Homes with existing forced-air ductwork
- Uses existing ducts
- Heats and cools
Cold-climate
Built to keep producing heat efficiently at low outdoor temperatures, which matters in a Toronto winter.
Best for: Homes that want a heat pump to carry more of the coldest days
- Works in deep cold
- More heat at low temps
Dual-fuel
Pairs a heat pump with a gas furnace. The heat pump handles most of the season and the furnace takes over in the coldest stretches.
Best for: Homes with a good gas furnace that want lower running costs most of the year
- Gas backup
- Lower running cost most months
How a visit goes
- 01
Tell us what it is doing
Call or send the form. Equipment, what it is doing, and where you are.
- 02
We look at it and give a straight answer
The whole system, including the part that did not fail yet. You get the options in plain words.
- 03
Fix or replace, your call
Written quote first. No work starts until you say so.
Sizing
Heat Pump Sizing for Toronto Homes
A heat pump has to be sized for heating first, and for how much heat it delivers when it is minus 15 °C outside. Size it like an AC and it cools fine in July and falls short in January. We do a load calculation on your house, compare it with the unit's low-temperature output, and check that it still handles summer humidity. If you keep a furnace for backup, we set up the controls so the two share the load properly.
Ductless bankRepair or replace
Keep and repair when
- It is a cold-climate model under 10 years old
- The fault is a sensor, board, or defrost control
- Refrigerant charge is the issue and there is no leak
- It performed fine last winter
Replace or upgrade when
- It is a standard model struggling every January
- The compressor or reversing valve has failed
- It was sized for cooling only
- You want to drop the gas furnace entirely
We check how the unit actually performs in your house at low temperatures before recommending anything.
What moves the price
Factors, not numbers. We quote after we see it.
Ducted or ductless
Ductless needs indoor heads and line sets for each room. Ducted uses the existing ductwork.
Cold-climate rating
Units built for deep cold cost more than standard heat pumps.
Backup heat source
Whether it pairs with an existing furnace as dual-fuel or needs electric backup heat.
Number of zones
More indoor heads on a ductless system means more installation work.
Electrical panel capacity
Some older houses need electrical work before a heat pump can go in.
Outdoor unit placement
Side yard, laneway, or wall bracket affects noise, snow clearance, and how easy the unit is to service.
Written quote after the visit. No work starts until you say so.
Heat pumps: brands we install and service












- Coaire
Ways to pay
Paying for an install
Ask about payment options when we quote the job. The written quote lists the equipment and the work, so you have the full number before you decide.
Ontario rebate, honestly framed
Ontario's Home Renovation Savings program currently covers qualifying heat pumps. Amounts change, and the homeowner claims it through a contractor registered with the program. Ask and we will tell you what applies to your house.
Heat pumps, answered
Do heat pumps work in Toronto winters?
Cold-climate models are built for it and keep producing heat well below freezing. Standard models lose output faster in deep cold, which is where a dual-fuel setup with a gas furnace helps. We size for the coldest nights.
Do I need to keep my gas furnace if I get a heat pump?
Not always. Some Toronto houses go heat-pump-only with electric backup, and others keep the furnace in a dual-fuel setup. It depends on the house, the heat loss, and how cold-climate-rated the heat pump is.
Can I get a heat pump in a house with radiators and no ducts?
Yes. A ductless heat pump uses wall or ceiling heads, so it adds cooling and extra heat without ductwork. The boiler and radiators can stay as the main heat or the backup. See our mini-split page for how the heads are placed.
Are there rebates for heat pumps in Ontario?
Ontario's Home Renovation Savings program currently covers qualifying heat pumps. Amounts change, and the homeowner claims it through a contractor registered with the program. Ask and we will tell you what applies to your house.
Will my electrical panel handle a heat pump?
Often, but older Toronto houses sometimes have small or full panels. We check the panel during the quote and tell you if it needs an electrician's attention first.
How is a heat pump sized?
By your house's heat loss and heat gain, and by how much heat the unit delivers at low outdoor temperatures. We calculate this on site, and size for heating first.
Heat pumps by area
Related services
Before you decide
- Heat pump cost in Ontario: what actually sets the price
- Heat pump vs. furnace in Toronto: how to choose
- Furnace replacement cost in Toronto: what sets the price
- Repair or replace your furnace: how to decide
- Should you replace your furnace and air conditioner together?
- AC not cooling? What to check before you call
- AC repair: what it costs and what to expect
Get a written quote for heat pumps
We call you back
At the number you gave us, to ask what the equipment is doing.
We book a window
A day and time that works. Scheduled visits outside the regular route.
Written quote before work
You see the number before anything is replaced. Nothing starts until you say so.